Overview

GSFP-TX

10/100/1000Base-T Copper Small Form Pluggable (SFP) transceivers is high performance, cost effective module compliant with the Gigabit Ethernet and 10/100/1000BASE-T standards as specified in IEEE 802. 3- 2002 and IEEE 802.3ab, which supporting 10/100/1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cables. The GSFP-TX supports 10/100/1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The GSFP-TX provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2wire serial bus at address ACh.

Features

      • Up to 1.25Gb/s bi-directional data links
      • Hot-pluggable SFP footprint
      • Extended case temperature range (0°C to +85°C )
      • Fully metallic enclosure for low EMI
      • Low power dissipation
      • Compact RJ-45 connector assembly
      • Detailed product information in EPROM
      •  +3.3V single power supply
      • Access to physical layer IC via 2-wire serial bus
      • 10/100/1000 BASE-T operation in host systems with SGMII interface
      • Compliant with SFP MSA

   Application

1.25 Gigabit Ethernet over Cat 5 cable

Switch/Router to Switch/Router Link

High level I/O for file servers
Other Optical links

Specification

Pin Description

Pin

Signal Name

Description

Plug Seq.

Notes

1

VEET

Transmitter Ground

1

2

TX FAULT

Transmitter Fault

Indication

3

Note1

3

TX DISABLE

Transmitter Disable

3

Note2

4

MOD_DEF(2)

SDA Serial Data Signal

3

Note3

5

MOD_DEF(1)

SCL Serial Clock Signal

3

Note3

6

MOD_DEF(0)

TTL Low

3

Note3

7

Rate Select

Not Connected

3

8

LOS

Loss of Signal

3

Note 4

9

VEER

Receiver ground

1

10

VEER

Receiver ground

1

11

VEER

Receiver ground

1

12

RX-

Inv. Received Data Out

3

Note 5

13

RX+

Received Data Out

3

Note 5

14

VEER

Receiver ground

1

15

VCCR

Receiver Power Supply

2

16

VCCT

Transmitter Power Supply

2

17

VEET

Transmitter Ground

1

18

TX+

Transmit Data In

3

Note 6

19

TX-

Inv. Transmit Data In

3

Note 6

20

VEET

Transmitter Ground

1

Notes:

Plug Seq.: Pin engagement sequence during hot plugging.

  1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
  2. 2)TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 ¨C 10 K resistor. Its states are:

Low (0 to 0.8V): Transmitter on

(>0.8, < 2.0V): Undefined

High (2.0 to 3.465V): Transmitter Disabled Open: Transmitter Disabled

  1. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K to 10K resistor on the host board. The pull-up voltage shall be VccT or VccR

Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID

Mod-Def 2 is the data line of two wire serial interface for serial ID

  1. 4)LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K to 10K resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to <0.8V.
  2. 5)RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with 100 (differential) at the user SERDES.
  3. 6)TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential terminations inside the module.

+3.3V Volt Electrical Power Interface

The SFP-GB-T3 has an input voltage range of +5V +/- 5%. The 3.3V maximum voltage is not allowed for continuous operation.

+3.3V Volt electrical power interface

+3.3V volt Electrical Power Interface

Parameter

Symbol

Min

Typ

Max

Units

Notes/Conditions

Supply Current

Is

320

375

mA

1.2W max power over full range of voltage and temperature.

See caution note below

Input Voltage

Vcc

3.13

3.3

3.47

V

Referenced to GND

Maximum

Vmax

4

V

Voltage

Surge Current

Isurge

30

mA

Hot plug above steady state current. See caution note below

Low-speed signals, electronic characteristics

Low-Speed Signals, Electronic Characteristics

Parameter

Symbol

Min

Max

Units

Notes/Conditions

SFP Output LOW

VOL

0

0.5

V

4.7k to 10k pull-up to host_Vcc, measured at host side of connector

SFP Output

HIGH

VOH

host_Vc

c – 0.5

host_Vc

c + 0.3

V

4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

SFP Input LOW

VIL

0

0.8

V

4.7k to 10k pull-up to Vcc, measured at SFP side of connector

SFP Input HIGH

VIH

2

Vcc + 0.3

V

4.7k to 10k pull-up to Vcc, measured at SFP side of connector

High-Speed Electrical Interface

High-Speed Electrical Interface Transmission Line-SFP

Parameter

Symbol

Min

Typ

Max

Units

Notes/Conditions

Line Frequency

fL

125

MHz

5-level encoding, per IEEE 802.3

Tx Output Impedance

Zout,TX

100

Ohm

Differential, for all Frequencies between 1MHz and 125MHz

Rx Input Impedance

Zin,RX

100

Ohm

Differential, for all Frequencies between 1MHz and 125MHz

High-speed electrical interface, host-SFP

High-Speed Electrical Interface, Host-SFP

Parameter

Symbol

Min

Typ

Max

Units

Notes/Conditions

Single ended data input

swing

Vinsing

250

1200

mV

Single ended

Single ended data output

swing

Voutsing

350

800

mV

Single ended

Rise/Fall Time

Tr,Tf

175

psec

20%-80%

Tx Input Impedance

Zin

50

Ohm

Single ended

Rx Output Impedance

Zout

50

Ohm

Single ended

General Specifications

General

Parameter

Symbol

Min

Typ

Max

Units

Notes/Conditions

Data Rate

BR

10

1,000

Mb/sec

IEEE 802.3 compatible.

See Notes 2 through 4 below

Cable

Length

L

100

m

Category 5 UTP. BER <10-12

Notes:

  1. Clock tolerance is +/- 50 ppm
  2. By default, the GSFP-Tx is a full duplex device in preferred master mode
  3. Automatic crossover detection is enabled. External crossover cable is not required
  4. 10/100/1000BASE-T operation requires the host system to have an SGMII interface with no clocks

Environmental Specifications

Environmental Specifications

Parameter

Symbol

Min

Typ

Max

Units

Notes/Conditions

Operating

Temperature

Top

-40

85

°C

Case temperature

Storage Temperature

Tsto

-40

100

°C

Ambient temperature

Mechanical Specifications

The host-side of the SFP-GB-T3 conforms to the mechanical specifications outlined in the SFP MSA1. The front portion of the SFP (part extending beyond the face plate of the host) is larger to accommodate the RJ- 45 connector.